Lately I've had a lot of little stuff going on, so I've just been picking at the bike little by little. I picked all the parts off the original frame and started installing them on the Primose frame. I got the engine in there and installed the new headset in the frame, then installed the forks. Funny thing (not so funny)- when I was torquing the triple crown nut down and had the forks flopped all the way over to one side, that small amount of effort knocked off the front steering lock stop that I had brazed onto the frame! I was astounded at how weak the bond was! Maybe when the frame went into the oven after powdercoating (twice) it weakened the braze? In any case, I had to sand down the surrounding surface and braze it on again!
Then there's that same problem that I had before with the front wheel bearings. After torquing the front axle, the spacer got smashed in there between both bearings that the bearings wouldn't spin anymore. So I thought that it might be different after I put in the new bearings- perhaps the old bearings were so loose that they moved too much. Well, after putting the new set of bearings in, the same thing happened! Argh!!! I think I'm going to just add a thin shim between one of the bearings and the spacer, hoping that it would create some relief. I'll get to that later- that problem isn't going anywhere.
I also had an issue that had been bugging me for a while- the pre-bent kickstarter lever that I bought from another forum member did not clear the Tarrozzi rearset peg. I somehow thought that it could be an issue with fitment from the Marsh frame, so I decided I would revisit the problem when I swapped the motor to the Primrose frame. Guess what?! The problem didn't go away!
I knew that the PO had purchased that kickstart lever from HVC and I also had the feeling like Fast From The Past had the exact same product, so I emailed them both to see if they knew of a fix. Brad from HVC had a fairly useless (unhelpful) response. Jim from FFTP suggested that perhaps the "boss" was not straight (the piece that actually clamped onto the spline). Since I had the original boss, I swapped out the parts, but it yielded the same results. I emailed the guy I bought the kickstarter from, just to give him a shout. He was very receptive and offered the refund my money if I chose to return it. I did still have the option of throwing some heat at the lever (the original straight lever for that matter), but I didn't really want to discolor the chrome. Part of me was saying that I shouldn't have to modify an already modified part- it should work as it was designed to work. I saw that there was a new and improved lever that HVC and FFTP was selling now. Jim said that if I bought a new lever from him and it didn't clear the peg, I could return it, so I pulled the trigger and bought another new lever. After almost 2 weeks of dicking around with this problem, I put the new lever on and guess what?! It clears the peg!! I emailed Jim and shared the good news. Problem solved!
So today I got a bunch of stuff done! I mounted the license plate and LED bolts (only to find out later that I had to rip it off the frame, since it wouldn't clear the rear tire), and the rear turn signals. I cut and installed the rear fender. I cabled up the carburetors and oil injector pump, then synced and adjusted the play on them. I installed all the carb overflow hoses. Then I mounted the rear wheel, cut and installed the chain. (That was a bitch, since I couldn't press out the pin, then I finally realized that I had 2 chain breaker tools sitting in my tool drawer!) I installed the clutch cable and adjusted the clutch lever. The clutch lever itself was a little sticky, so I had to sand down the surfaces a little to relieve the pressure points.
All in all, it was a pretty productive day. More positives than negatives. Can't beat that with a stick.
Then there's that same problem that I had before with the front wheel bearings. After torquing the front axle, the spacer got smashed in there between both bearings that the bearings wouldn't spin anymore. So I thought that it might be different after I put in the new bearings- perhaps the old bearings were so loose that they moved too much. Well, after putting the new set of bearings in, the same thing happened! Argh!!! I think I'm going to just add a thin shim between one of the bearings and the spacer, hoping that it would create some relief. I'll get to that later- that problem isn't going anywhere.
I also had an issue that had been bugging me for a while- the pre-bent kickstarter lever that I bought from another forum member did not clear the Tarrozzi rearset peg. I somehow thought that it could be an issue with fitment from the Marsh frame, so I decided I would revisit the problem when I swapped the motor to the Primrose frame. Guess what?! The problem didn't go away!
I knew that the PO had purchased that kickstart lever from HVC and I also had the feeling like Fast From The Past had the exact same product, so I emailed them both to see if they knew of a fix. Brad from HVC had a fairly useless (unhelpful) response. Jim from FFTP suggested that perhaps the "boss" was not straight (the piece that actually clamped onto the spline). Since I had the original boss, I swapped out the parts, but it yielded the same results. I emailed the guy I bought the kickstarter from, just to give him a shout. He was very receptive and offered the refund my money if I chose to return it. I did still have the option of throwing some heat at the lever (the original straight lever for that matter), but I didn't really want to discolor the chrome. Part of me was saying that I shouldn't have to modify an already modified part- it should work as it was designed to work. I saw that there was a new and improved lever that HVC and FFTP was selling now. Jim said that if I bought a new lever from him and it didn't clear the peg, I could return it, so I pulled the trigger and bought another new lever. After almost 2 weeks of dicking around with this problem, I put the new lever on and guess what?! It clears the peg!! I emailed Jim and shared the good news. Problem solved!
So today I got a bunch of stuff done! I mounted the license plate and LED bolts (only to find out later that I had to rip it off the frame, since it wouldn't clear the rear tire), and the rear turn signals. I cut and installed the rear fender. I cabled up the carburetors and oil injector pump, then synced and adjusted the play on them. I installed all the carb overflow hoses. Then I mounted the rear wheel, cut and installed the chain. (That was a bitch, since I couldn't press out the pin, then I finally realized that I had 2 chain breaker tools sitting in my tool drawer!) I installed the clutch cable and adjusted the clutch lever. The clutch lever itself was a little sticky, so I had to sand down the surfaces a little to relieve the pressure points.
All in all, it was a pretty productive day. More positives than negatives. Can't beat that with a stick.
No comments:
Post a Comment